Dynalco SC-2124M Scanner/Monitor Bedienungsanleitung

1 3690 N.W. 53rd Street Fort Lauderdale, FL 33309 SC-2124 SC-2124M 24 Channel Universal Scanner Installation and Operation Manual P/N 1

102.2 Wiring (Cont’d) Connectors D and E are input terminals, each requiring p/n SC-CBLE25MM cable / terminal block assembly. Thermocouples can be

11 Connector E (DB-25F) This Connector provides the Analog Inputs for Channels 13 – 24. Pinout: Pin# Pin Name Pin# Pin Name 1 Channel 1

122.2 Wiring (Cont’d) Optional DB cables and DB-to-Screw -Terminal DIN-RAIL Modules are available CONN

133.0 Setup The SC-2124 requires the user to configure a variety of parameters: SCANNER channel analog inputs; ALARM & SHUTDOWN TRIP conditions;

143.1.1 Setup Screen The SCANNER has the capability of communicating via Dynalink (point to point) using the communications cable p/n CBLE-8509 or v

15 3.1.2 Configuration File The easiest method for the user to configure the SC-2124 is by editing and downloading a configuration file to the SCANN

164.0 Standard Operation After power-up, the SC-2124 performs all standard SCANNER operations continually. These operations include scanning all en

174.1 RESET After power-up, the SC-2124 starts up in a RESET condition that assumes that all channels are in a non-fault state, initializes the ALAR

184.3 ALARM The SCANNER provides a precautionary ALARM warning to alert the user to potentially hazardous or dangerous input conditions. The SCANNE

195.0 User Interface The SC-2124 user interface located on the front panel of the SCANNER consists of a large-character, 4-row by 20-column, backlit

2TABLE OF CONTENTS 1.0 Introduction 3 1.1 Ratings & Certification 6 2.0 Installation 7 2.

20 Figure 2, Run Screens DYNALCO CONTROLS SCAN-2124 V1.00 0 10 - + MAIN SCAN CUSTOM CH SNAP 10 0100 200 110 120SCN CH01 ENG

215.2 Run Screens The main purpose of the SC-2124 Run Screens is to allow the user to navigate to and from screens that display current run-time val

22After startup, the user may navigate to the Title Screen from the Main Menu Screen. This allows the user to adjust the LCD contrast at any time du

235.2.4 SCAN Screen The SCAN Screen is the default SCANNER screen. The SCAN Screen displays each enabled scanner channel for three seconds (delay i

245.2.6.1 HELP Screens In addition to viewing the channel’s current analog input reading, the Channel Screen provides a link to channel HELP Screens

25 Appendix A This appendix contains a table of all parameter numbers found in the SCAN2124.SPC file. Use this appendix to keep track of the values

26Scan Screen Settings Parameter Description Valid Inputs 195= Selects type of scan screen to view (default or 0= displays default screen (enabled

27Channel 1 Input Settings Parameter Function Description Valid Inputs 110.1= Channel name for CH01 Default=” “ (blank=CH01) 11 characters (inclu

28Channel 2 Input Settings Parameter Function Description Valid Inputs 110.2= Channel name for CH02 Default=” “ (blank=CH02) 11 characters (inclu

29Appendix C Channel 3 Input Settings Parameter Function Description Valid Inputs 110.3= Channel name for CH03 Default=” “ (blank=CH03) 11 charac

31.0 Introduction The SC-2124 is a microprocessor-based universal scanner for continuous monitoring of up to 24 channels measuring temperature from

30Channel 4 Input Settings Parameter Function Description Valid Inputs 110.4= Channel name for CH04 Default=” “ (blank=CH04) 11 characters (inclu

31Appendix C Channel 5 Input Settings Parameter Function Description Valid Inputs 110.5= Channel name for CH05 Default=” “ (blank=CH05) 11 charac

32Channel 6 Input Settings Parameter Function Description Valid Inputs 110.6= Channel name for CH06 Default=” “ (blank=CH06) 11 characters (inclu

33Appendix C Channel 7 Input Settings Parameter Function Description Valid Inputs 110.7= Channel name for CH07 Default=” “ (blank=CH07) 11 charac

34Channel 8 Input Settings Parameter Function Description Valid Inputs 110.8= Channel name for CH08 Default=” “ (blank=CH08) 11 characters (inclu

35Appendix C Channel 9 Input Settings Parameter Function Description Valid Inputs 110.9= Channel name for CH09 Default=” “ (blank=CH09) 11 charac

36Channel 10 Input Settings Parameter Function Description Valid Inputs 110.10= Channel name for CH10 Default=” “ (blank=CH10) 11 characters (inc

37Appendix C Channel 11 Input Settings Parameter Function Description Valid Inputs 110.11= Channel name for CH 11 Default=” “ (blank=CH11) 11 cha

38Channel 12 Input Settings Parameter Function Description Valid Inputs 110.12= Channel name for CH12 Default=” “ (blank=CH12) 11 characters (inc

39Appendix C Channel 13 Input Settings Parameter Function Description Valid Inputs 110.13= Channel name for CH13 Default=” “ (blank=CH13) 11 char

41.1 Packaging Front View 6.55"8.50"

40Channel 14 Input Settings Parameter Function Description Valid Inputs 110.14= Channel name for CH14 Default=” “ (blank=CH14) 11 characters (inc

41Appendix C Channel 15 Input Settings Parameter Function Description Valid Inputs 110.15= Channel name for CH15 Default=” “ (blank=CH15) 11 char

42Channel 16 Input Settings Parameter Function Description Valid Inputs 110.16= Channel name for CH16 Default=” “ (blank=CH16) 11 characters (inc

43Appendix C Channel 17 Input Settings Parameter Function Description Valid Inputs 110.17= Channel name for CH17 Default=” “ (blank=CH17) 11 char

44Channel 18 Input Settings Parameter Function Description Valid Inputs 110.18= Channel name for CH18 Default=” “ (blank=CH18) 11 characters (inc

45Appendix C Channel 19 Input Settings Parameter Function Description Valid Inputs 110.19= Channel name for CH19 Default=” “ (blank=CH19) 11 char

46Channel 20 Input Settings Parameter Function Description Valid Inputs 110.20= Channel name for CH20 Default=” “ (blank=CH20) 11 characters (inc

47Appendix C Channel 21 Input Settings Parameter Function Description Valid Inputs 110.21= Channel name for CH21 Default=” “ (blank=CH21) 11 char

48Channel 22 Input Settings Parameter Function Description Valid Inputs 110.22= Channel name for CH22 Default=” “ (blank=CH22) 11 characters (inc

49Appendix C Channel 23 Input Settings Parameter Function Description Valid Inputs 110.23= Channel name for CH23 Default=” “ (blank=CH23) 11 char

5Rear View CONN ECONN DCONN ACONN CANALOGINPUTS 1-12RELAYCONTACTS (1) RLY 1 N/C (3) RLY 1 COM. (5) RLY 1 N/O (7) RLY 2 N/C (9) RLY 2

50Channel 24 Input Settings Parameter Function Description Valid Inputs 110.24= Channel name for CH24 Default=” “ (blank=CH24) 11 characters (inc

51Appendix C User-defined Trips User Trip Class Parameter Define the trip class for: Valid Inputs 63000.49= user trip 01 0=Class A over (defaul

52User Trip Timer Valid Inputs Parameter Sets the delay time between: 63003.49= exceeded user trip 01 threshold and channel fault63003.50= exceed

53Appendix C Meter Channel Sources Sets the channel to view on: Valid inputs: 0 = off (default) 1 to 24= analog input channel

53APPENDIX B. Example of a Configuration File (SCAN2124.SPC) ;***************************************************************************** ;

54/*$PAGE*/ ; ************** SCAN SCREEN ************** ; Main SCANNER Screen. ; 0 (dflt) SCAN screen displays all ; ENABLED

55/*$PAGE*/ ; ************ AI DELAY TIMERS ************ ; CHANNEL READ DLY TIME ******************* ; Dly time between analog sw setup & analo

56 /*$PAGE*/ ; ************ AI CHANNEL #01 ************* ; <ANALOG INPUT CHANNEL #01> ; AI CH NAME ****************************** ; User-def

57 ; AI CH FILTER CONSTANT ******************* ; Averages new AI readings into current AI ; value by the following equation: ; ; AI = [AI_prev

58/*$PAGE*/ ; AI CH ALARM & SHUTDOWN TRIP CLASS ******* ; 0 Off (dflt) ; 1 Class A Over ; 2 Class B Over ;

6 1.2 Specifications 1. Input Channels:24 Thermocouple (J,K,T, or E), 0 – 5V, or 4 – 20mA (On-Board 100 Ohm resistor provided on Channels 1 thro

59/*$PAGE*/ ; ************ AI CHANNEL #02 ************* ; <ANALOG INPUT CHANNEL #02> ; AI CH NAME ****************************** ; User-defi

60 ; AI CH FILTER CONSTANT ******************* ; Averages new AI readings into current AI ; value by the following equation: ; ; AI = [AI_prev

61/*$PAGE*/ ; AI CH ALARM & SHUTDOWN TRIP CLASS ******* ; 0 Off (dflt) ; 1 Class A Over ; 2 C

62/*$PAGE*/ ; ************** USER TRIPS *************** ; USER-defined TRIPs allow mapping from ; any Analog Input channels (or RPM input) ; to

6363001.58=0 ; <USER TRIP #10> ; USER TRIP HYS *************************** ; TRIP hysteresis; difference between fault ; threshold o

64/*$PAGE*/ ; USER TRIP SOURCE ************************ ; 0 OFF (dflt) ; 1-24 AI Channels ; 25 RPM 121.1=0 ; <USER TRIP #

65/*$PAGE*/ ; *************** RPM TRIPS *************** ; !!!!!! Only if RPM Input available !!!!!! ; ***************************************** ; R

66/*$PAGE*/ ; ************* METER MODULE ************** ; !!! Only if Digital METERs available !!!! ; ***************************************** ; **

67APPENDIX C Instructions for Downloading WinHost from Dynalco website: 1. Go to the www.Dynalco.com web site. Start by clicking on the “Support”

68APPENDIX D Modbus Addresses (SC-2124M Only) These addresses are all RUN time related (Function Code 03) RANGE CHANNELS VALUE INTEGER D

72.0 Installation Installation requires a cutout as shown in section 2.1 along with four mounting holes. Once the unit is mounted, a nearby (less

69APPENDIX E Instructions for SC-RTD configuration: The SC-RTD module is required for any inputs to be configured for RTD type inputs. Each module

8 2.2 Wiring Connector A (DB-15M): This Connector is used for the DC Power Input and the Cold Junction Compensation (CJC) Sensor Input. In additi

92.2 Wiring (Cont’d) Connector C (DB-25M) This Connector provides Contact Outputs for the 4 on-board relays. Pinout: Pin# Pin Name 1 Relay 1 NC